Steep Sites and Sloping Driveways in Queenstown and Wanaka: Gradients, Drainage and Non-Slip Finishes
Under the
Queenstown Lakes District Plan, a private vehicle access can't be steeper than 1 in 6, which is about 17%. In a residential zone where the access serves no more than two residential units, it can go up to 1 in 5 (20%), as long as the average gradient stays no steeper than 1 in 6, the first 6 m from the road boundary is no steeper than 1 in 6, and the surface is sealed with a non-slip finish.
1The Gradient Rules in Plain English
The general limit is 1 in 6 (about 17%) for any private way used for vehicle access.1
The 1 in 5 (20%) exception applies only in residential zones where the access serves no more than two residential units.1
Under the exception, the average gradient over the full length can't be steeper than 1 in 6, and the first 6 m from the road boundary can't be steeper than 1 in 6.1
The surface must be sealed with a non-slip finish.1
Gradient is measured on the centreline of the access, and vehicle break-over angles can't be exceeded.1
Drainage on a Slope
On a steep site, water moves fast. A sloping driveway should be shaped with a crown or crossfall so that water leaves the surface, and drainage should send it away from the garage, the house and neighbouring land, not toward them. The base also matters. Poorly compacted ground on a slope can settle or move, which cracks the concrete above it.
Non-Slip Finishes
Surface texture matters more than colour on a steep driveway, and it's a requirement for the 1 in 5 exception.
1 A broom finish gives a ridged, gripping surface, and exposed aggregate gives a rougher, textured one. Smooth, power-floated concrete is slippery when wet or frosty, so it isn't a good choice for a slope. Our
guide to choosing a driveway finish compares plain, coloured and exposed aggregate finishes.
Frost, Shade and Steep Sites
Questions to Ask Before You Pour
What's the gradient on the centreline, and how does it compare with the council limit
Does the design meet the break-over angle requirements
How will water drain away from the garage and neighbouring land
What finish gives the best grip, and is it sealed with a non-slip finish
How will the base be prepared on the slope
Frequently Asked Questions
What is the maximum driveway gradient in Queenstown?
The Queenstown Lakes District Plan limits a private vehicle access to 1 in 6, about 17%. In residential zones where it serves no more than two residential units it can reach 1 in 5, with conditions on the average gradient, the first 6 m and a non-slip surface.1
What is a 1 in 6 slope as a percentage?
A 1 in 6 slope rises 1 m for every 6 m of length, which is about 17%. A 1 in 5 slope rises 1 m for every 5 m, which is exactly 20%.
Can a driveway be steeper than 1 in 6 in Queenstown?
In residential zones where the access serves no more than two residential units, up to 1 in 5 is allowed if the average gradient is no steeper than 1 in 6, the first 6 m from the road is no steeper than 1 in 6, and the surface is non-slip.1
What finish is best for a steep concrete driveway?
Choose a textured finish such as a broom finish or exposed aggregate, because it grips better than smooth, power-floated concrete when it's wet or frosty. The council's 1 in 5 exception also requires a sealed, non-slip surface.1
How do you stop water running down a sloping driveway into the garage?
Shape the driveway with a crown or crossfall so water leaves the surface, and plan drainage to carry it away from the garage, the house and neighbouring land. Ask your contractor and designer how they'll handle run-off on your site.
Does Letton work in Wanaka and Queenstown?
Yes. We cover Wanaka, Queenstown, Cromwell and the wider Central Otago area. If your site is further out, call 03 344 1597 and we'll tell you whether we can help.3
Sources
1. Queenstown Lakes District Plan, Transport Rules (June 2022) — Queenstown Lakes District Council. The maximum gradient of 1 in 6 for any private way used for vehicle access, the 1 in 5 exception in residential zones, the non-slip sealing requirement, measurement on the centreline and the break-over angle rule.